What could be the cause of an uncommanded roll at high speed?How does altitude affect the speed of sound?What was the first aircraft that could fly inverted?How could a failed left wing cause a roll to the right?What is the difference between a forward, aft, high and low center of gravity?What is the direction convention for Roll angle?Why do aircraft have a crossover airspeed, and why does it increase at higher vertical load factors?Why was the 737 main rudder servo valve’s vulnerability to causing uncommanded reversals never discovered in testing?Why does the A320’s maximum allowable aileron deflection decrease, rather than increase, when the flaps are extended?Why not use the yoke to control yaw, as well as pitch and roll?What is the THS deflection speed?
How were concentration and extermination camp guards recruited?
How many times can you cast a card exiled by Release to the Wind?
Deformation of rectangular plot
Strange symbol for two functions
Where does this pattern of naming products come from?
My coworkers think I had a long honeymoon. Actually I was diagnosed with cancer. How do I talk about it?
2.8 is missing the Carve option in the Boolean Modifier
Question about JavaScript Math.random() and basic logic
What's up with this leaf?
How to make horizontal space between a dot and a text equal to horizontal space between the dot of numerical label of numbered list and its item?
What can cause the front wheel to lock up when going over a small bump?
Are "living" organ banks practical?
Should an arbiter claim draw at a K+R vs K+R endgame?
Implement Homestuck's Catenative Doomsday Dice Cascader
Why does the Schrödinger equation work so well for the Hydrogen atom despite the relativistic boundary at the nucleus?
Building a road to escape Earth's gravity by making a pyramid on Antartica
Why does Kathryn say this in 12 Monkeys?
Why only the fundamental frequency component is said to give useful power?
Turing patterns
Do you need type ratings for private flying?
What are the peak hours for public transportation in Paris?
Do simulator games use a realistic trajectory to get into orbit?
Translating 'Liber'
Why doesn’t a normal window produce an apparent rainbow?
What could be the cause of an uncommanded roll at high speed?
How does altitude affect the speed of sound?What was the first aircraft that could fly inverted?How could a failed left wing cause a roll to the right?What is the difference between a forward, aft, high and low center of gravity?What is the direction convention for Roll angle?Why do aircraft have a crossover airspeed, and why does it increase at higher vertical load factors?Why was the 737 main rudder servo valve’s vulnerability to causing uncommanded reversals never discovered in testing?Why does the A320’s maximum allowable aileron deflection decrease, rather than increase, when the flaps are extended?Why not use the yoke to control yaw, as well as pitch and roll?What is the THS deflection speed?
$begingroup$
I have a problem with a T-38. There is uncommanded roll to the left when the aircraft flies at 250 knots. But as the aircraft speed goes up around 500 knots, the uncommanded roll is now to the right. During 500 knots we could control the plane with 15-20 aileron trims.
What may be the problem?
We have replaced a lot of systems and cylinders. And we changed the travel limits of aileron, flap, rudder, and horizontal stabilizer. But no change has been observed.
flight-controls t-38
edited May 29 at 11:52
Rodrigo de Azevedo
8381519
asked May 28 at 11:55
Emrah CeylanEmrah Ceylan
175
New contributor
Emrah Ceylan is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
|
show 4 more comments
$begingroup$
I have a problem with a T-38. There is uncommanded roll to the left when the aircraft flies at 250 knots. But as the aircraft speed goes up around 500 knots, the uncommanded roll is now to the right. During 500 knots we could control the plane with 15-20 aileron trims.
What may be the problem?
We have replaced a lot of systems and cylinders. And we changed the travel limits of aileron, flap, rudder, and horizontal stabilizer. But no change has been observed.
flight-controls t-38
edited May 29 at 11:52
Rodrigo de Azevedo
8381519
asked May 28 at 11:55
Emrah CeylanEmrah Ceylan
175
New contributor
Emrah Ceylan is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
8
$begingroup$
It would probably help a lot if you indicated what aircraft you were referring to. Obviously, at 500 kt IAS, you're probably not talking about a Cessna 150, but there are a lot of aircraft that will hit 500kt.
$endgroup$
– FreeMan
May 28 at 12:08
$begingroup$
Have you inspected the geometry of the wings?
$endgroup$
– ratchet freak
May 28 at 12:19
3
$begingroup$
You may wish to edit to clarify this -- as posted, it reads that you have left at low speed, then left at high speed. If, as I suspect, they're opposite, this is different from the case where they're the same direction.
$endgroup$
– Zeiss Ikon
May 28 at 12:21
$begingroup$
Have you checked the aileron actuating system and associated hydraulic lines?
$endgroup$
– Juan Jimenez
May 28 at 13:06
2
$begingroup$
So both at 250 and at 500 knots the uncommanded roll is to the left?
$endgroup$
– Koyovis
May 28 at 13:24
|
show 4 more comments
$begingroup$
I have a problem with a T-38. There is uncommanded roll to the left when the aircraft flies at 250 knots. But as the aircraft speed goes up around 500 knots, the uncommanded roll is now to the right. During 500 knots we could control the plane with 15-20 aileron trims.
What may be the problem?
We have replaced a lot of systems and cylinders. And we changed the travel limits of aileron, flap, rudder, and horizontal stabilizer. But no change has been observed.
flight-controls t-38
edited May 29 at 11:52
Rodrigo de Azevedo
8381519
asked May 28 at 11:55
Emrah CeylanEmrah Ceylan
175
New contributor
Emrah Ceylan is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
I have a problem with a T-38. There is uncommanded roll to the left when the aircraft flies at 250 knots. But as the aircraft speed goes up around 500 knots, the uncommanded roll is now to the right. During 500 knots we could control the plane with 15-20 aileron trims.
What may be the problem?
We have replaced a lot of systems and cylinders. And we changed the travel limits of aileron, flap, rudder, and horizontal stabilizer. But no change has been observed.
flight-controls t-38
flight-controls t-38
edited May 29 at 11:52
Rodrigo de Azevedo
8381519
asked May 28 at 11:55
Emrah CeylanEmrah Ceylan
175
New contributor
Emrah Ceylan is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited May 29 at 11:52
Rodrigo de Azevedo
8381519
asked May 28 at 11:55
Emrah CeylanEmrah Ceylan
175
New contributor
Emrah Ceylan is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited May 29 at 11:52
Rodrigo de Azevedo
8381519
edited May 29 at 11:52
Rodrigo de Azevedo
8381519
edited May 29 at 11:52
Rodrigo de Azevedo
8381519
8381519
asked May 28 at 11:55
Emrah CeylanEmrah Ceylan
175
New contributor
Emrah Ceylan is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked May 28 at 11:55
Emrah CeylanEmrah Ceylan
175
asked May 28 at 11:55
Emrah CeylanEmrah Ceylan
175
175
New contributor
Emrah Ceylan is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Emrah Ceylan is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
8
$begingroup$
It would probably help a lot if you indicated what aircraft you were referring to. Obviously, at 500 kt IAS, you're probably not talking about a Cessna 150, but there are a lot of aircraft that will hit 500kt.
$endgroup$
– FreeMan
May 28 at 12:08
$begingroup$
Have you inspected the geometry of the wings?
$endgroup$
– ratchet freak
May 28 at 12:19
3
$begingroup$
You may wish to edit to clarify this -- as posted, it reads that you have left at low speed, then left at high speed. If, as I suspect, they're opposite, this is different from the case where they're the same direction.
$endgroup$
– Zeiss Ikon
May 28 at 12:21
$begingroup$
Have you checked the aileron actuating system and associated hydraulic lines?
$endgroup$
– Juan Jimenez
May 28 at 13:06
2
$begingroup$
So both at 250 and at 500 knots the uncommanded roll is to the left?
$endgroup$
– Koyovis
May 28 at 13:24
|
show 4 more comments
8
$begingroup$
It would probably help a lot if you indicated what aircraft you were referring to. Obviously, at 500 kt IAS, you're probably not talking about a Cessna 150, but there are a lot of aircraft that will hit 500kt.
$endgroup$
– FreeMan
May 28 at 12:08
$begingroup$
Have you inspected the geometry of the wings?
$endgroup$
– ratchet freak
May 28 at 12:19
3
$begingroup$
You may wish to edit to clarify this -- as posted, it reads that you have left at low speed, then left at high speed. If, as I suspect, they're opposite, this is different from the case where they're the same direction.
$endgroup$
– Zeiss Ikon
May 28 at 12:21
$begingroup$
Have you checked the aileron actuating system and associated hydraulic lines?
$endgroup$
– Juan Jimenez
May 28 at 13:06
2
$begingroup$
So both at 250 and at 500 knots the uncommanded roll is to the left?
$endgroup$
– Koyovis
May 28 at 13:24
8
8
$begingroup$
It would probably help a lot if you indicated what aircraft you were referring to. Obviously, at 500 kt IAS, you're probably not talking about a Cessna 150, but there are a lot of aircraft that will hit 500kt.
$endgroup$
– FreeMan
May 28 at 12:08
$begingroup$
It would probably help a lot if you indicated what aircraft you were referring to. Obviously, at 500 kt IAS, you're probably not talking about a Cessna 150, but there are a lot of aircraft that will hit 500kt.
$endgroup$
– FreeMan
May 28 at 12:08
$begingroup$
Have you inspected the geometry of the wings?
$endgroup$
– ratchet freak
May 28 at 12:19
$begingroup$
Have you inspected the geometry of the wings?
$endgroup$
– ratchet freak
May 28 at 12:19
3
3
$begingroup$
You may wish to edit to clarify this -- as posted, it reads that you have left at low speed, then left at high speed. If, as I suspect, they're opposite, this is different from the case where they're the same direction.
$endgroup$
– Zeiss Ikon
May 28 at 12:21
$begingroup$
You may wish to edit to clarify this -- as posted, it reads that you have left at low speed, then left at high speed. If, as I suspect, they're opposite, this is different from the case where they're the same direction.
$endgroup$
– Zeiss Ikon
May 28 at 12:21
$begingroup$
Have you checked the aileron actuating system and associated hydraulic lines?
$endgroup$
– Juan Jimenez
May 28 at 13:06
$begingroup$
Have you checked the aileron actuating system and associated hydraulic lines?
$endgroup$
– Juan Jimenez
May 28 at 13:06
2
2
$begingroup$
So both at 250 and at 500 knots the uncommanded roll is to the left?
$endgroup$
– Koyovis
May 28 at 13:24
$begingroup$
So both at 250 and at 500 knots the uncommanded roll is to the left?
$endgroup$
– Koyovis
May 28 at 13:24
|
show 4 more comments
3 Answers
3
active
oldest
votes
$begingroup$
I once went on-site to troubleshoot an airliner with an uncommanded roll problem. The operator had rigged this and rigged that and were in the process of ordering new aileron power control units, pretty much out of desperation. I asked about the trim actuator, which they had replaced with a known good unit off another aircraft, making them think that couldn't be the problem. I centered the trim and went to look at the position of the rig pin holes in the aileron control circuit. They were mis-aligned.
The trim actuator on this airplane was an electric linear type with an internal Linear Variable Displacement Transducer (LVDT), that supplied the position signal to the cockpit trim indicator (or EICAS in this case), that was "dithering", that is, the signal was drifting around. When you thought the trim was centered, it was actually offset, and this error would randomly change as the actuator was moved. On the original airplane the actuator was installed on, the dithering wasn't enough to cause a snag to be raised by the flight crew so its internal problem went undetected.
The variations in roll you saw at speed may be some other phenomenon, or it just could have been coincidental variations in the trim indication on that flight.
So, if it was me, the trim system itself would be an item to cross off the list before proceeding to more desperate measures. Do a thorough functional test of the trim system and its indication, and also look for things like backlash within the actuator itself or in the linkage.
answered May 28 at 12:51
John KJohn K
30.6k149100
$endgroup$
$begingroup$
It sounds like roll trim is a function of speed, not a random dither.
$endgroup$
– Koyovis
May 28 at 13:26
5
$begingroup$
Maybe, maybe not. You would have to go out and do a carefully documented series of tests to establish what is going on precisely. Was the shift with speed a direct, repeatable condition or just a one time coincidence. We don't have all the information and are just spitballing here. Golden rule of troubleshooting: eliminate the easy/cheap things first.
$endgroup$
– John K
May 28 at 13:38
add a comment |
$begingroup$
If this were a model aircraft with a wide speed range (like, say, a hand launch glider), I'd expect this to be a cross-trim problem. Generally, the rudder will have more authority at lower speeds, while aileron will gain authority as speed increases.
Based on that, I'd suggest verifying the rigging of the airframe; look for a fin, rudder, or rudder trim that's generating yaw in the direction of your lower speed uncommanded roll (yaw will produce roll due to whatever mechanism provides roll stability). The aileron trim that offsets that uncommanded yaw will overpower it as speed increases, producing your uncommanded roll in the opposite direction.
answered May 28 at 12:18
Zeiss IkonZeiss Ikon
4,137621
$endgroup$
$begingroup$
Good answer but if it were a model, I'd suspect that something was broken or loose and moving under the increased aerodynamic load of high speed. Or an incorrect thrust line.
$endgroup$
– Robin Bennett
May 29 at 8:40
$begingroup$
@RobinBennett A thrust line problem is tied to power setting; it'll happen during takeoff/launch even more than at high speed (because less aero forces on the surfaces at low speed and high power). Broken or loose will be erratic.
$endgroup$
– Zeiss Ikon
May 29 at 10:55
add a comment |
$begingroup$
If the flight control is a hydraulic system, have you changed the fluid recently, if yes you need to purge the system for air bubbles, otherwise you need to check the fluid quality for impurity.
answered May 28 at 12:49
user40476user40476
438110
$endgroup$
add a comment |
Your Answer
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "528"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Emrah Ceylan is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f64832%2fwhat-could-be-the-cause-of-an-uncommanded-roll-at-high-speed%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
3 Answers
3
active
oldest
votes
3 Answers
3
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
I once went on-site to troubleshoot an airliner with an uncommanded roll problem. The operator had rigged this and rigged that and were in the process of ordering new aileron power control units, pretty much out of desperation. I asked about the trim actuator, which they had replaced with a known good unit off another aircraft, making them think that couldn't be the problem. I centered the trim and went to look at the position of the rig pin holes in the aileron control circuit. They were mis-aligned.
The trim actuator on this airplane was an electric linear type with an internal Linear Variable Displacement Transducer (LVDT), that supplied the position signal to the cockpit trim indicator (or EICAS in this case), that was "dithering", that is, the signal was drifting around. When you thought the trim was centered, it was actually offset, and this error would randomly change as the actuator was moved. On the original airplane the actuator was installed on, the dithering wasn't enough to cause a snag to be raised by the flight crew so its internal problem went undetected.
The variations in roll you saw at speed may be some other phenomenon, or it just could have been coincidental variations in the trim indication on that flight.
So, if it was me, the trim system itself would be an item to cross off the list before proceeding to more desperate measures. Do a thorough functional test of the trim system and its indication, and also look for things like backlash within the actuator itself or in the linkage.
answered May 28 at 12:51
John KJohn K
30.6k149100
$endgroup$
$begingroup$
It sounds like roll trim is a function of speed, not a random dither.
$endgroup$
– Koyovis
May 28 at 13:26
5
$begingroup$
Maybe, maybe not. You would have to go out and do a carefully documented series of tests to establish what is going on precisely. Was the shift with speed a direct, repeatable condition or just a one time coincidence. We don't have all the information and are just spitballing here. Golden rule of troubleshooting: eliminate the easy/cheap things first.
$endgroup$
– John K
May 28 at 13:38
add a comment |
$begingroup$
I once went on-site to troubleshoot an airliner with an uncommanded roll problem. The operator had rigged this and rigged that and were in the process of ordering new aileron power control units, pretty much out of desperation. I asked about the trim actuator, which they had replaced with a known good unit off another aircraft, making them think that couldn't be the problem. I centered the trim and went to look at the position of the rig pin holes in the aileron control circuit. They were mis-aligned.
The trim actuator on this airplane was an electric linear type with an internal Linear Variable Displacement Transducer (LVDT), that supplied the position signal to the cockpit trim indicator (or EICAS in this case), that was "dithering", that is, the signal was drifting around. When you thought the trim was centered, it was actually offset, and this error would randomly change as the actuator was moved. On the original airplane the actuator was installed on, the dithering wasn't enough to cause a snag to be raised by the flight crew so its internal problem went undetected.
The variations in roll you saw at speed may be some other phenomenon, or it just could have been coincidental variations in the trim indication on that flight.
So, if it was me, the trim system itself would be an item to cross off the list before proceeding to more desperate measures. Do a thorough functional test of the trim system and its indication, and also look for things like backlash within the actuator itself or in the linkage.
answered May 28 at 12:51
John KJohn K
30.6k149100
$endgroup$
$begingroup$
It sounds like roll trim is a function of speed, not a random dither.
$endgroup$
– Koyovis
May 28 at 13:26
5
$begingroup$
Maybe, maybe not. You would have to go out and do a carefully documented series of tests to establish what is going on precisely. Was the shift with speed a direct, repeatable condition or just a one time coincidence. We don't have all the information and are just spitballing here. Golden rule of troubleshooting: eliminate the easy/cheap things first.
$endgroup$
– John K
May 28 at 13:38
add a comment |
$begingroup$
I once went on-site to troubleshoot an airliner with an uncommanded roll problem. The operator had rigged this and rigged that and were in the process of ordering new aileron power control units, pretty much out of desperation. I asked about the trim actuator, which they had replaced with a known good unit off another aircraft, making them think that couldn't be the problem. I centered the trim and went to look at the position of the rig pin holes in the aileron control circuit. They were mis-aligned.
The trim actuator on this airplane was an electric linear type with an internal Linear Variable Displacement Transducer (LVDT), that supplied the position signal to the cockpit trim indicator (or EICAS in this case), that was "dithering", that is, the signal was drifting around. When you thought the trim was centered, it was actually offset, and this error would randomly change as the actuator was moved. On the original airplane the actuator was installed on, the dithering wasn't enough to cause a snag to be raised by the flight crew so its internal problem went undetected.
The variations in roll you saw at speed may be some other phenomenon, or it just could have been coincidental variations in the trim indication on that flight.
So, if it was me, the trim system itself would be an item to cross off the list before proceeding to more desperate measures. Do a thorough functional test of the trim system and its indication, and also look for things like backlash within the actuator itself or in the linkage.
answered May 28 at 12:51
John KJohn K
30.6k149100
$endgroup$
I once went on-site to troubleshoot an airliner with an uncommanded roll problem. The operator had rigged this and rigged that and were in the process of ordering new aileron power control units, pretty much out of desperation. I asked about the trim actuator, which they had replaced with a known good unit off another aircraft, making them think that couldn't be the problem. I centered the trim and went to look at the position of the rig pin holes in the aileron control circuit. They were mis-aligned.
The trim actuator on this airplane was an electric linear type with an internal Linear Variable Displacement Transducer (LVDT), that supplied the position signal to the cockpit trim indicator (or EICAS in this case), that was "dithering", that is, the signal was drifting around. When you thought the trim was centered, it was actually offset, and this error would randomly change as the actuator was moved. On the original airplane the actuator was installed on, the dithering wasn't enough to cause a snag to be raised by the flight crew so its internal problem went undetected.
The variations in roll you saw at speed may be some other phenomenon, or it just could have been coincidental variations in the trim indication on that flight.
So, if it was me, the trim system itself would be an item to cross off the list before proceeding to more desperate measures. Do a thorough functional test of the trim system and its indication, and also look for things like backlash within the actuator itself or in the linkage.
answered May 28 at 12:51
John KJohn K
30.6k149100
answered May 28 at 12:51
John KJohn K
30.6k149100
answered May 28 at 12:51
John KJohn K
30.6k149100
answered May 28 at 12:51
John KJohn K
30.6k149100
30.6k149100
$begingroup$
It sounds like roll trim is a function of speed, not a random dither.
$endgroup$
– Koyovis
May 28 at 13:26
5
$begingroup$
Maybe, maybe not. You would have to go out and do a carefully documented series of tests to establish what is going on precisely. Was the shift with speed a direct, repeatable condition or just a one time coincidence. We don't have all the information and are just spitballing here. Golden rule of troubleshooting: eliminate the easy/cheap things first.
$endgroup$
– John K
May 28 at 13:38
add a comment |
$begingroup$
It sounds like roll trim is a function of speed, not a random dither.
$endgroup$
– Koyovis
May 28 at 13:26
5
$begingroup$
Maybe, maybe not. You would have to go out and do a carefully documented series of tests to establish what is going on precisely. Was the shift with speed a direct, repeatable condition or just a one time coincidence. We don't have all the information and are just spitballing here. Golden rule of troubleshooting: eliminate the easy/cheap things first.
$endgroup$
– John K
May 28 at 13:38
$begingroup$
It sounds like roll trim is a function of speed, not a random dither.
$endgroup$
– Koyovis
May 28 at 13:26
$begingroup$
It sounds like roll trim is a function of speed, not a random dither.
$endgroup$
– Koyovis
May 28 at 13:26
5
5
$begingroup$
Maybe, maybe not. You would have to go out and do a carefully documented series of tests to establish what is going on precisely. Was the shift with speed a direct, repeatable condition or just a one time coincidence. We don't have all the information and are just spitballing here. Golden rule of troubleshooting: eliminate the easy/cheap things first.
$endgroup$
– John K
May 28 at 13:38
$begingroup$
Maybe, maybe not. You would have to go out and do a carefully documented series of tests to establish what is going on precisely. Was the shift with speed a direct, repeatable condition or just a one time coincidence. We don't have all the information and are just spitballing here. Golden rule of troubleshooting: eliminate the easy/cheap things first.
$endgroup$
– John K
May 28 at 13:38
add a comment |
$begingroup$
If this were a model aircraft with a wide speed range (like, say, a hand launch glider), I'd expect this to be a cross-trim problem. Generally, the rudder will have more authority at lower speeds, while aileron will gain authority as speed increases.
Based on that, I'd suggest verifying the rigging of the airframe; look for a fin, rudder, or rudder trim that's generating yaw in the direction of your lower speed uncommanded roll (yaw will produce roll due to whatever mechanism provides roll stability). The aileron trim that offsets that uncommanded yaw will overpower it as speed increases, producing your uncommanded roll in the opposite direction.
answered May 28 at 12:18
Zeiss IkonZeiss Ikon
4,137621
$endgroup$
$begingroup$
Good answer but if it were a model, I'd suspect that something was broken or loose and moving under the increased aerodynamic load of high speed. Or an incorrect thrust line.
$endgroup$
– Robin Bennett
May 29 at 8:40
$begingroup$
@RobinBennett A thrust line problem is tied to power setting; it'll happen during takeoff/launch even more than at high speed (because less aero forces on the surfaces at low speed and high power). Broken or loose will be erratic.
$endgroup$
– Zeiss Ikon
May 29 at 10:55
add a comment |
$begingroup$
If this were a model aircraft with a wide speed range (like, say, a hand launch glider), I'd expect this to be a cross-trim problem. Generally, the rudder will have more authority at lower speeds, while aileron will gain authority as speed increases.
Based on that, I'd suggest verifying the rigging of the airframe; look for a fin, rudder, or rudder trim that's generating yaw in the direction of your lower speed uncommanded roll (yaw will produce roll due to whatever mechanism provides roll stability). The aileron trim that offsets that uncommanded yaw will overpower it as speed increases, producing your uncommanded roll in the opposite direction.
answered May 28 at 12:18
Zeiss IkonZeiss Ikon
4,137621
$endgroup$
$begingroup$
Good answer but if it were a model, I'd suspect that something was broken or loose and moving under the increased aerodynamic load of high speed. Or an incorrect thrust line.
$endgroup$
– Robin Bennett
May 29 at 8:40
$begingroup$
@RobinBennett A thrust line problem is tied to power setting; it'll happen during takeoff/launch even more than at high speed (because less aero forces on the surfaces at low speed and high power). Broken or loose will be erratic.
$endgroup$
– Zeiss Ikon
May 29 at 10:55
add a comment |
$begingroup$
If this were a model aircraft with a wide speed range (like, say, a hand launch glider), I'd expect this to be a cross-trim problem. Generally, the rudder will have more authority at lower speeds, while aileron will gain authority as speed increases.
Based on that, I'd suggest verifying the rigging of the airframe; look for a fin, rudder, or rudder trim that's generating yaw in the direction of your lower speed uncommanded roll (yaw will produce roll due to whatever mechanism provides roll stability). The aileron trim that offsets that uncommanded yaw will overpower it as speed increases, producing your uncommanded roll in the opposite direction.
answered May 28 at 12:18
Zeiss IkonZeiss Ikon
4,137621
$endgroup$
If this were a model aircraft with a wide speed range (like, say, a hand launch glider), I'd expect this to be a cross-trim problem. Generally, the rudder will have more authority at lower speeds, while aileron will gain authority as speed increases.
Based on that, I'd suggest verifying the rigging of the airframe; look for a fin, rudder, or rudder trim that's generating yaw in the direction of your lower speed uncommanded roll (yaw will produce roll due to whatever mechanism provides roll stability). The aileron trim that offsets that uncommanded yaw will overpower it as speed increases, producing your uncommanded roll in the opposite direction.
answered May 28 at 12:18
Zeiss IkonZeiss Ikon
4,137621
answered May 28 at 12:18
Zeiss IkonZeiss Ikon
4,137621
answered May 28 at 12:18
Zeiss IkonZeiss Ikon
4,137621
answered May 28 at 12:18
Zeiss IkonZeiss Ikon
4,137621
4,137621
$begingroup$
Good answer but if it were a model, I'd suspect that something was broken or loose and moving under the increased aerodynamic load of high speed. Or an incorrect thrust line.
$endgroup$
– Robin Bennett
May 29 at 8:40
$begingroup$
@RobinBennett A thrust line problem is tied to power setting; it'll happen during takeoff/launch even more than at high speed (because less aero forces on the surfaces at low speed and high power). Broken or loose will be erratic.
$endgroup$
– Zeiss Ikon
May 29 at 10:55
add a comment |
$begingroup$
Good answer but if it were a model, I'd suspect that something was broken or loose and moving under the increased aerodynamic load of high speed. Or an incorrect thrust line.
$endgroup$
– Robin Bennett
May 29 at 8:40
$begingroup$
@RobinBennett A thrust line problem is tied to power setting; it'll happen during takeoff/launch even more than at high speed (because less aero forces on the surfaces at low speed and high power). Broken or loose will be erratic.
$endgroup$
– Zeiss Ikon
May 29 at 10:55
$begingroup$
Good answer but if it were a model, I'd suspect that something was broken or loose and moving under the increased aerodynamic load of high speed. Or an incorrect thrust line.
$endgroup$
– Robin Bennett
May 29 at 8:40
$begingroup$
Good answer but if it were a model, I'd suspect that something was broken or loose and moving under the increased aerodynamic load of high speed. Or an incorrect thrust line.
$endgroup$
– Robin Bennett
May 29 at 8:40
$begingroup$
@RobinBennett A thrust line problem is tied to power setting; it'll happen during takeoff/launch even more than at high speed (because less aero forces on the surfaces at low speed and high power). Broken or loose will be erratic.
$endgroup$
– Zeiss Ikon
May 29 at 10:55
$begingroup$
@RobinBennett A thrust line problem is tied to power setting; it'll happen during takeoff/launch even more than at high speed (because less aero forces on the surfaces at low speed and high power). Broken or loose will be erratic.
$endgroup$
– Zeiss Ikon
May 29 at 10:55
add a comment |
$begingroup$
If the flight control is a hydraulic system, have you changed the fluid recently, if yes you need to purge the system for air bubbles, otherwise you need to check the fluid quality for impurity.
answered May 28 at 12:49
user40476user40476
438110
$endgroup$
add a comment |
$begingroup$
If the flight control is a hydraulic system, have you changed the fluid recently, if yes you need to purge the system for air bubbles, otherwise you need to check the fluid quality for impurity.
answered May 28 at 12:49
user40476user40476
438110
$endgroup$
add a comment |
$begingroup$
If the flight control is a hydraulic system, have you changed the fluid recently, if yes you need to purge the system for air bubbles, otherwise you need to check the fluid quality for impurity.
answered May 28 at 12:49
user40476user40476
438110
$endgroup$
If the flight control is a hydraulic system, have you changed the fluid recently, if yes you need to purge the system for air bubbles, otherwise you need to check the fluid quality for impurity.
answered May 28 at 12:49
user40476user40476
438110
answered May 28 at 12:49
user40476user40476
438110
answered May 28 at 12:49
user40476user40476
438110
answered May 28 at 12:49
user40476user40476
438110
438110
add a comment |
add a comment |
Emrah Ceylan is a new contributor. Be nice, and check out our Code of Conduct.
Emrah Ceylan is a new contributor. Be nice, and check out our Code of Conduct.
Emrah Ceylan is a new contributor. Be nice, and check out our Code of Conduct.
Emrah Ceylan is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Aviation Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f64832%2fwhat-could-be-the-cause-of-an-uncommanded-roll-at-high-speed%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
8
$begingroup$
It would probably help a lot if you indicated what aircraft you were referring to. Obviously, at 500 kt IAS, you're probably not talking about a Cessna 150, but there are a lot of aircraft that will hit 500kt.
$endgroup$
– FreeMan
May 28 at 12:08
$begingroup$
Have you inspected the geometry of the wings?
$endgroup$
– ratchet freak
May 28 at 12:19
3
$begingroup$
You may wish to edit to clarify this -- as posted, it reads that you have left at low speed, then left at high speed. If, as I suspect, they're opposite, this is different from the case where they're the same direction.
$endgroup$
– Zeiss Ikon
May 28 at 12:21
$begingroup$
Have you checked the aileron actuating system and associated hydraulic lines?
$endgroup$
– Juan Jimenez
May 28 at 13:06
2
$begingroup$
So both at 250 and at 500 knots the uncommanded roll is to the left?
$endgroup$
– Koyovis
May 28 at 13:24